Tds_xyladecor_total_wood_care_.doc

TECHNICAL DATA SHEET XYLADECOR
Xyladecor Total Wood Care is the ultimate preservation and protection product. Its Triple Action Formula,
protects, treats and enhances the natural wood. It is suitable for exterior and interior use on new or pre-
treated wood. It penetrates deep into the wood. It does not peel or blister. Protects against wood destroying
insects and blue stain fungi. If using inside, apply Xyladecor Total Wood Care and then apply a top coat,
we recommend Xyladecor Total Varnish.
Suitable for wooden houses, chalets, wood panelling, parts of the structure or cladding for external walls,
and fencing. Not suitable for wood in permanent contact with the ground or water.
Exterior and Interior Use

PRODUCT INFORMATION
PRODUCT INFORMATION

Type : Solvent-borne woodstain containing UV absorbing pigments and active ingredients
effective against bluestain fungi and wood-boring insects.

Pack Size : 750ml, 2.5L and 5L
Composition (nominal) Pigment: UV absorbing and other pigments (not in colourless).

Binder: Oleoresinous

Solvent: Low odour aliphatic hydrocarbons.
Active ingredients: dichlofluanid (0.55%), permethrin (0.03%)
Specific gravity : approx. 0.86

Viscosity : thin free-flowing liquid

Thinning : Ready for use-do not thin.

Application Method : Brush

Spreading Rates : 1 litre is enough to treat 5 m2 in 2 – 3 coats. Rough wood may be more
absorbent than smooth planed wood.

Touch Dry : about 4 – 6 hours
Recoatable : about 12 hours.

Fully dry : about 24 hours.
Drying time will vary according to temperature, humidity and surface, i.e. the drying times quoted will be
significantly longer in cold, damp conditions or on non-absorbent or oily wood. Although products dry within
24 hours, the full mechanical and chemical resistance of the finish will take longer to fully develop.

VOC (Volatile Organic : EU-limit value for this product (Cat. A/f): 700 g/l (2010). This product contains
Compounds) VOC.

Cleaning Up : After use, remove as much product from the brush as possible before cleaning
with white spirit. Spills may be cleaned up with white spirit whilst still wet. SURFACE PREPARATION

General: All traces of grease, wax and polish must be completely removed. Wood should be dry.
New or bare wood: Clean weathered and dirty wood using a stiff brush, detergent and water. Rinse and
allow to dry. Grey weathered wood should be sanded to a clean bright surface.
Wood previously treated with a penetrating treatment, i.e. Xyladecor Total Wood Care: Remove any
loose or defective coating. Touch up bare areas before final coats.
Wood previously treated with a paint, varnish or other film-forming product: this must be removed by
scraping or sanding. Then treat as bare wood.
SURFACE PREPARATION
S
YSTEM INFORMATION
SYSTEM INFORMATION
APPLICATION
Stir or shake well before and during use. Apply 2 – 3 even coats with a brush to achieve a total application
rate of 5m²/litre. Apply in the direction of the wood grain, taking care to produce an even finish and avoid
overlap. Wipe with a dry brush 15-20 minutes after application to achieve a uniform appearance. To achieve
maximum protection, apply to all surfaces. Apply a minimum of 3 coats to end-grain surfaces to reduce the
washing out of coloured wood extracts, which may stain other surfaces.
Do not use the colourless version on wood directly exposed to the weather. When used on interior wood,
apply a topcoat, such as a colourless varnish. We recommend Xyladecor Total Varnish.
SAFETY, HEALTH & ENVIR
ONMENTAL INFORMA
ETY, HEALTH & ENVIRONMENTAL INFORMATION
SOLVENT-BASED WOODSTAIN
Hazard-determining components of labelling Dichlofluanid (ISO), Permethrin, Naphtha (Petroleum), hydrotreated heavy Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic
environment.
Harmful: may cause lung damage if swallowed.
Repeated exposure may cause skin dryness or cracking.
Keep away from food, drink and animals feeding stuffs. After contact with skin, wash immediately with plenty of soap and water. Wear suitable protective clothing, gloves and eye/face protection. Avoid release to the environment. Refer to special instructions/safety data sheets. If swallowed, do not induce vomiting: seek medical advice immediately and show this container or label. Contains Dichlofluanid (ISO), 2-Butanonoxim. May produce an allergic reaction. Safety Precautions When sanding use a dust mask. Do not breathe in the sanding dust. Never apply by spraying. During and after application provide a well-ventilated area. When working do not eat, drink or smoke. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. Take off immediately off
contaminated clothing. After inhalation supply fresh air, consult doctor in case of symptoms.
Use biocides safely. Always read the label and product information before use.
Greek approval number?

Storage and Waste Disposal
Store the product only in the original container and not above of temperatures of +30°C for long times. Do
not empty product and cleaning residues into drains, aquatic environment and soil.
Dispose of cans which are completely empty (drip-free) at your materials recycling centre. Dispose of
cleaning residues and cans which are not completely empty in accordance with the local Regulations
(hazard waste collection point).
European waste catalogue: 030202
For further advice contact
Xyladecor and the ICI Roundel are Trademarks of ICI. ICI 07 (070307IT)

Source: http://www.xyladecor.gr/en/products/TDS/tds_xyladecor_total_wood_care.pdf